For an obligation free demonstration in the Auckland area call or text 021 347 942
The Smoke Pro™ Total-Tech™ from Redline Detection
Vacumn Leaks
Exhaust Leaks
Oil Leaks
Bent Valves
And More....
Test every car you service, takes minutes to set up, and turn before unseen faults and leaks into more turnover in your workshop!
|
Smoke Pro™ Total-Tech™
This tool is designed for serious workshops and technicians. It is the most advanced smoke machine available to date. This advanced design eliminates the need for nitrogen when testing an
EVAP system. The Total Tech™ on White Medicinal Mineral Oil H-1 (baby oil) and does not require annual oil changes. The Total-Tech™ utilizes two stage regulation to
precisely deliver smoke or air at the approved EVAP test pressure of 1214 inches of water column. The Total-Tech™ provides the operator with a pressure gauge as well as a flowmeter. These components allow the technician to test any system using
pressure decay in seconds, and to visually detect the rate of leakage on the flowmeter. The Total-Tech™ also incorporates a Flow Control Valve. This valve also allows the technician the versatility to pinpoint a leak without the masking effect of
excessive smoke. The Total-Tech™ compact design allows the unit to hang under the bonnet or chassis during testing. Machined from billet aerospace aluminum and stainless steel, the Total-Tech™ is made in America and unconditionally
warranted for one full year.
Watch The Video
To download a brochure click here 
|
FIND AIR LEAKS AND ENGINE FAULTS FAST !
The Smoke Pro™ Total-Tech™ is a must diagnostic tool for any vehicle repair workshop!
Can you remember how many times you have had a vehicle in the workshop that has been running rough or has a number of lean diagnostic trouble codes, or you suspect an air leak and have sprayed tins of easy start or CRC around the maifold to find
it.
How many hours have those jobs taken?
Have you been able to charge out all of those hours?
With the Smoke Pro™ Total-Tech™ you can find inlet air leaks, PCV faults, inter cooler, turbo leaks and more, in a fraction of the time, first time, everytime!
You can even check for bent valves if the cam timing belt has snapped before you replace the belt along with expensive tensioner kits!
We use one ourselfs to help diagnose these problems and really would not be without it!
The unit makes smoke under pressure from nothing more than baby oil, it runs on 12 volts powered from the vehicle and is very easy to use.
It also comes with a full 12 month warrantee.
| |
Operators Quick Reference Manual
Components and Accessories
The following list is designed to familiarize you with the location and function of the operational components of the machine. The list also includes the supplied accessories and how to use
them.
A Flow Control Valve
- Location: The Flow Control Valve is located on the front of the machine directly under the cycle Start/Stop button. It is a round knurled knob.
- Function: In many cases excessive smoke exiting a leak may make it difficult to determine the exact location of the leak. The purpose of the Flow Control
Valve is to decrease the amount of smoke exiting a leak so that its position may be pinpointed without the masking effect of excessive smoke. Turn clockwise to decrease flow, counterclockwise to increase flow. This valve is also used to lock out the system
under test and observe any pressure decay on the pressure gauge.
B Start/Stop Button
- Location: The Start/Stop Button is located in the front of the machine directly under the Output Pressure Gauge.
- Function: Depressing the Start/Stop Button will start a 5-minute smoke producing cycle. To interrupt this cycle, press the Start/Stop Button again and the
smoke production will stop. If the cycle is not interrupted, the smoke production will terminate automatically in 5 minutes. Once the leak has been located, it is recommended to stop the smoke production using this button rather than turning the Flow Control
Valve to the fully closed position.
C Flowmeter
- Location: The flowmeter is located on the right side of the machine.
- Function: The purpose of the flowmeter is to provide a quick visual indication of the amount of air passing through the system being tested. If the smoke
supply nozzle is in a closed system, and there are no leaks in that system, the flowmeter will read zero (ball at bottom of scale). As a system is filled with air or smoke, the ball in the flowmeter will slowly fall to the bottom of the scale as the pressure
in the system equalizes to the output pressure of the Smoke Pro". As the flow decreases, the output pressure will increase. If the flowmeter ball never falls to the bottom of the scale, there is leakage or air passing through the system. It is not necessary
to use smoke when using the flowmeter to determine if a leak exists.
D Output Pressure Gauge
- Location: The Output Pressure Gauge is located directly on top of the machine.
- Function: The Output Pressure Gauge displays the output pressure of the machine. The gauge is calibrated to read Inches of Water and PSI. When the machine is
connected to a system, the pressure within that system becomes equal to the output pressure of the machine. While deadheading the Smoke Pro" (by placing your thumb over the smoke supply nozzle) the gauge will indicate the maximum output pressure.
- Pressure Decay Test: This gauge can also be used to determine if a leak exists by closing the Flow Control Valve while the system is under pressure. If the
gauge holds the displayed pressure, there is no leakage. If the displayed pressure starts dropping when the Flow Control Valve is closed there is leakage in the system. Note: DO NOT perform pressure decay tests with smoke. The heat produced by the smoke
generator will cause erroneous readings.
E Dip Stick (Checking oil level)
- Location: The Dip Stick is located on the top of the Smoke Pro".
- Function: To check and confirm proper oil level.
F Cap Plugs
- Description: An assortment of yellow Cap Plugs ranging from 3/16 to 3.9 is provided with your Smoke Pro".
- Function: Cap Plugs are used to seal openings in the system under test. Your set has been designed to seal most automotive systems. (See Vacuum Leak Testing
below for other methods of sealing the air intake).
G Exhaust Cone Adaptor
- Description: The Exhaust Cone Adapter is a black rubber cone that tapers from 3 ½ to 1 in diameter and is 6 inches in length with a short length of 3/8
hose at its center to direct the smoke through.
- Function: The Exhaust Cone Adaptor is a very useful tool. The adaptor is designed to help find exhaust leaks by inserting it into the tail pipe and filling
the cold exhaust system with smoke. By inserting the supplied 3/8 Cap Plug into the hose leading from the Exhaust Cone, it also serves as a plug to seal the exhaust while testing for vacuum leaks under the hood. The Exhaust Cone Adaptor also works well to
seal the intake tube at the air filter box and allow smoke to enter the engine without disconnecting anything else.
H OBD-II Service Port Adaptor
- Description: The Service Port Adaptor is a female brass fitting with a 2 length of black 3/8 diameter hose attached.
- Function: The Service Port Adaptor is designed to connect the Smoke Supply Nozzle to the OBD-II EVAP Service Port. This port provides access to the Fuel
Vapor Recovery System (EVAP) for inspection and test. Connecting the Smoke Pro" to this port allows the technician to determine if a leak exists and to quickly locate the leak with smoke. Note: The Schrader Valve must be removed from the service port before
installing the Service Port Adaptor. This valve has left-hand threads.
I Schrader Valve Removal Tool
- Description: The Schrader Valve Removal Tool looks like a small screw driver with a slot at the end. The tool supplied with your Smoke Pro? has a different
size tool at each end.
- Function: The Schrader Valve Removal Tool is used to remove the Schrader Valve from the OBD-II service port before connecting the Service Port Adaptor. Note:
The service port is normally under the bonnet and is usually green in color.
J Hook
-
Your new Smoke Pro" comes with a handy stainless steel hook for conveniently hanging the machine under the bonnet or chassis.
For more infomation please about Smoke Pro™ Total-Tech™
Contact Us
|
|
