All testing is performed with the engine off!

1 Setting up the Smoke Pro"

2 Vacuum Leak Testing.

• Select an appropriate vacuum line to access the vacuum system. The brake booster supply line before the check valve is a good choice.
• Seal system openings such as the air intake. If the brake booster line or any other line leading to the intake manifold is selected for the test connection, the air intake must be sealed to prevent smoke from leaking back through the intake. If the vehicle has a round inlet tube from the air filter, the Exhaust Cone adaptor will seal this opening without disturbing other connections and may serve as the access point for smoke. Otherwise, to seal the intake, use the supplied plugs, a latex glove or cellophane wrap with a rubber band. If none of these methods are possible, pack the venturis with cellophane using a soft stick or the end of a pencil. Seal the exhaust pipe using the supplied Exhaust Cone, a latex glove or rag. Note: To use the Exhaust Cone as a plug, you must seal the 3/8 diameter inlet on the Exhaust Cone with the yellow cap plug provided.
• Set up the machine for operation per Item 1 above.
• This procedure will not only locate leaks in vacuum lines but in many other components such as; EGR valves, oil seals and gaskets, idle motors and solenoids, intercoolers and turbochargers, injector o-rings, ducting, throttle shafts, base gaskets, diaphragms, canisters and fittings to name a few. Important!! It is always best to test in a draft free area. Always use a bright halogen lamp to enhance the visibility of the smoke exiting the leak.

3 Exhaust Leak Testing

• Insert the Exhaust Cone Adaptor into the end of the tailpipe. If the automobile has dual exhaust with a cross over pipe, simply plug the other pipe with a rag, tape, or latex glove with a rubber band.
• Set-up the machine for operation per Item 1 above.
• This test is most effective when the exhaust system is cold. Small leaks are sometimes sealed as the exhaust system heats up due to thermal expansion. A hot catalytic converter may consume some of the smoke in front of the converter. Remember, all testing is performed with the engine off!

4 Under Dash Leaks

• Most vehicles have a common vacuum line leading from the dashboard, through the firewall, to a vacuum source under the hood. This line supplies vacuum to climate control functions and other vacuum operated systems. Locate this line under the hood and disconnect it at its source. We will use this line to check under the dashboard for leaks.
• Set up the machine for operation per Item 1 above.
• While pressure or smoke is being fed into the vacuum supply line, observe the Flowmeter or Output Pressure Gauge. Change the climate control selector lever or button from heat to vent, to defrost, etc. As the lever is moved, a change in the flowmeter or pressure gauge reading will determine which system is leaking. Set the lever in the position that registered a reading while looking for the leak under the dashboard using a bright halogen lamp. This method will thoroughly inspect this system for leakage.
• Inspection of the central locking system is performed in the same manner. Access the control solenoids and activate them while introducing smoke into the system.

5 Fuel Vapor Recovery System (EVAP)

• According to the Environmental Protection Agency, the EVAP system is the most neglected of all the emission systems in an automobile. A leak as small as 0.020 diameter can allow over 30 times the allowable hydrocarbons into the atmosphere then is currently acceptable through the exhaust. Additionally, EVAP system leaks can be a major cause of check engine lights occurring. In the past, EVAP related problems have been difficult to locate and repair. These can now be quickly diagnosed and repaired, becoming a profitable ticket for service facilities.
• There are several acceptable methods of inspecting the EVAP system. Basically we need to close any vent solenoids, fill the system with smoke, and look for the smoke escaping at the leak. Since these systems vary in different vehicles and have evolved over the years, we will attempt to describe operating guidelines that should be helpful in inspecting these EVAP systems.
• Beginning with the 1996 model year, U.S. Vehicles have been produced with an EVAP Service Port to access this system. The port is usually located under the hood, but may be located else were on the vehicle. To access this port for testing, remove the cap, then remove the Schrader Valve from inside the Service Port, using the supplied Schrader Valve Removal Tool. Important Note: The Schrader Valve has left-hand threads, turn clockwise to remove! Connect the supplied Service Port Adaptor to the Service Port.
• The Onboard Diagnostics on vehicles 1996 and beyond will determine if a leak exists, the following trouble codes may be indicated to report the leak:
  PO442 for a .040 leak standard
  PO456 for a .020 leak standard
• Using a scan tool, close the vent solenoids so that the EVAP system is closed to the atmosphere.
• Set up the machine for operation per Item 1 above.
• Remove the fuel cap and begin to fill the system through the Service Port Adaptor until dense smoke is seen exiting the fuel neck. This procedure ensures that the system is full of smoke. Replace the fuel cap and continue pumping smoke into the system.
• Inspect under the hood for leaks using a bright halogen lamp. Raise the vehicle on a hoist and inspect the underside of the vehicle, tracing the route of the EVAP system. Note: It may be necessary to hang the Smoke Pro" under the car so that it is visible to the operator.
• As the system fills with smoke, and the pressure in the system equalizes, keep an eye on the Flowmeter and the Pressure Gauge. If there is no leakage in the system the Pressure Gauge will go to its maximum pressure and the Flowmeter will drop to zero.
• For trouble code PO456, the meter should stabilize at 0.1 LPM or less with the Smoke Pro".
• For trouble code PO442, the meter should stabilize at 0.5 LPM or less with the Smoke Pro".
  Note: These readings are approximate and are for reference only.
• Once the leak has been located and repaired, it is a good idea to repeat the above procedure using air only. It is not necessary to turn on the smoke to test for leakage using the Flowmeter.
• Replace Schrader Valve and cover. (Note: Valve is Left-hand thread.)

Following are some generic OBD EVAP related codes:

P0443 Purge Control Valve Circuit
P0444 Purge Control Valve Circuit Open
P0445 Purge Control Valve Circuit Shorted
P0446 Vent Control Circuit
P0447 Vent Control Circuit Open
P0448 Vent Control Circuit Shorted
P0449 Vent Valve/Solenoid Circuit
P0450 Pressure Sensor
P0451 Pressure Sensor Range/Performance
P0452 Pressure Sensor Low Input
P0453 Pressure Sensor High Input
P0454 Pressure Sensor Intermittent
P0455 System Leak Detected (gross leak)
P0456 System Leak Detected (very small leak)
P0457 System Leak Detected (fuel cap loose/off)
P0465 EVAP Purge Flow Sensor Circuit
P0466 EVAP Purge Flow Sensor Circuit Range/Performance
P0467 EVAP Purge Flow Sensor Circuit Low Input
P0468 EVAP Purge Flow Sensor Circuit High Input
P0469 EVAP Purge Flow Sensor Circuit Intermittent

Maintenance

Oil Level:
Check the oil level regularly, approximately every 50 tests or so. Always be sure the gasket is in place and tighten the Dip Stick firmly when replacing. The oil level should be maintained between the high and low hash marks on the Dip Stick. When filling a new machine, add 4 oz of mineral oil. If the machine has been previously filled and drained, only 2 oz of oil is required to fill it. Oil can be purchased from any retail store. To add oil to the Smoke Pro", simply pour oil into the Dip Stick hole. Note: It takes approximately 2 oz to raise the level from the low to high mark. Due to the high purity of the mineral oil supplied, it may sometimes be difficult to read the Dip Stick. An alternate method for determining fluid level is to drain the oil from the machine and refill with 2 oz of mineral oil.
Use only medicinal mineral oil or baby oil that does not contain any lotions, aloe, vegetable oil or creams. An added fragrance is acceptable

Flowmeter:
It may be necessary to provide periodic maintenance to your flowmeter. If the ball in the meter sticks, an immediate correction can be made by tapping the flowmeter. If this happens frequently, it will be necessary to clean the meter.
Disassembly: Remove the top-plug ball stop. Take out the ball or float by inverting the flowmeter and allowing the ball to fall in your hand. (Note: it is best to cover the discharge port to avoid losing the float through the opening.)
Cleaning: The float tube and flowmeter body can be easily cleaned with a small amount of pure soap and water. A long Q-tip will aid with the cleaning. Avoid harsh agents like acetone or benzene, or any other agents that may contain chlorinated solvents and avoid prolonged immersion.
Reassembly: Reinstall the float and replace the top-plug. A little grease on the O ring will help maintain a good seal as well as facilitate assembly. For additional Flowmeter information, contact Dwyer Instruments at www.dwyer-inst.com

Trouble Shooting

No air flow

" Check that air is connected to machine
" Check that Flow Control Valve is open
" Check that the Smoke Supply hose is not kinked or pushed into machine

Poor smoke density or volume

" Check that oil level is correct
" Check that Flow Control Valve is open
" Check that battery is fully charged
" Check that the Smoke Supply hose is not restricted

Green power lamp does not light

" Check for proper connection to battery
" Check for correct polarity connection
(Red to Positive, Black to Negative)
" Check that battery is fully charged

Flowmeter sticks

" Clean meter per maintenance instructions (If frequent cleaning is required, the air supply may be contaminated)

Flowmeter bounces

" Oil condensed in Smoke Supply Hose (See note below)

Pressure Gauge bounces

" Oil condensed in Smoke Supply Hose (See note below)

Red lamp is flashing

" Check that battery is fully charged and connections are tight.
" Contact factory

Green lamp is flashing

" Check that battery is fully charged and connections are tight

High test pressure reading during a smoke producing cycle

" Check that the Smoke Supply hose is not kinked or pushed into machine
" Check that the Smoke Supply hose is not deadheaded

Oil Condensed in Smoke Supply Hose:
Due to the high density smoke produced by the Smoke Pro" oil may condense in the Smoke Supply Hose. This is normal. Condensed oil may cause the Flowmeter and Pressure Gauge readings to bounce and a gurgling or percolating sound to come from the hose. Should this occur, elevate the Smoke Pro" and let the full length of the hose hang down into a container to catch the small amount of oil in the hose as it drains. For best results, leave the Smoke Pro" in this position overnight.

Warranty
Redline Detection LLC (Redline) warrants all Redline products to be free from defects in workmanship or material under normal use and service for a period of one-year from the date of purchase by the end-user. Liability under this warranty is limited to either (1) repair or replacement F.O.B. Redlines facility of any parts or products which prove to be defective within the one-year warranty period or (2) repayment of the purchase price provided the products have been returned shipping prepaid within the one year warranty period, at Redlines sole option. Products are only to be used by persons having skill and knowledge in the automotive repair field, and improper use or maintenance may cause serious injury. In no event shall Redline be liable beyond replacement of products F.O.B. Redlines facility or refund of the full purchase price. This warranty shall be void if a product is improperly maintained, altered, abused or otherwise misused in any way.

EXCEPT AS SET FORTH IN THIS WRITTEN WARRANTY, REDLINE EXPRESSLY DISCLAIMS ANY AND ALL REPRESENTATIONS AND WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF TITLE, NON-INFRINGEMENT, MERCHANTIBILITY OR FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT, TRADEMARK, OR OTHER RIGHTS OR ANY OTHER EXPRESS OR IMPLIED WARRANTIES.

THE PURCHASERS SOLE REMEDY FOR ANY DEFECTIVE PRODUCT SHALL BE REPLACEMENT OR REFUND AS STATED ABOVE AND REDLINE SHALL NOT BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, INDIRECT OR PUNITIVE DAMAGES ON ACCOUNT OF DEFECTIVE PRODUCTS, HOWEVER CAUSED, UNDER ANY THEORY OF LIABILITY.